top of page

Finding Excess Moisture in Your Home: Attic Case Study

Writer: Tom Bickford
Tom Bickford
Aug 26
4 min read

Moisture is one of the most important things a home inspector looks for during an inspection—and one of the easiest problems for homeowners to overlook.


Excess moisture doesn't necessarily mean that water is actively leaking into the house. It can come from condensation, inadequate ventilation, ground moisture, plumbing leaks, roof leaks, or simply the way a house is being heated and ventilated.


The important thing is finding the moisture before it becomes a much bigger problem.


The high humidity attic

On a recent inspection, we found evidence of high humidity in an attic. It wasn’t present at the time of the inspection, but the evidence was.



The nails used to fasten the roof sheathing had extensive surface rust and surface mold growth was evident on the end wall plywood sheathing.


This is an important distinction. The moisture wasn't necessarily coming through the roof. It was likely related to moisture accumulating within the attic space.


Warm, moist air from the living space can migrate into an attic through ceiling penetrations, light fixtures, wiring holes, plumbing penetrations, attic hatches, and other openings. If the attic isn't adequately ventilated, that moisture can condense on colder surfaces.


Since this inspection was during the summer, when temperatures were excessively high and humidity is likely higher outside the house than inside, moisture wasn’t migrating into the attic like it might during the winter. Also hot surfaces generally don’t give you a condensation problem. But during the colder months, when the outside moisture content is low and the inside moisture content is high, the moisture tries to travel from the inside to the outside (attic) and condense on the cold surfaces. Attic vapor barriers and proper ventilation take care of this. 


On this inspection, we also noticed that the temperature in the attic was 128° F while the outside temperature was only 95° F. The normal temperature difference should only be 10-20°. This 33° difference was telling us that there is a real ventilation issue in this attic. 


Note, we also had to do an abbreviated attic inspection because of the high temperature. 128° F is dangerous to work in. Working time needs to be kept to 5 minutes max and there should be someone who is acting as your watcher, usually from the attic way. And remember, if you pass out up there, you’ll be in that heat until the fire department can get there and rescue you, which usually means another 20+ minutes. This can cause permanent bodily damage and possibly death, so never take high temperatures for granted.


Looking at the house, we saw that soffit and ridge vents had been installed, as seen from the outside. And looking inside the attic, we could see that the attic baffles were in place. It isn’t the job of a home inspector to tell you WHY a problem is occurring, even if we have our suspicions. 


We know three things about this house. 

  1. There is excessive moisture in the attic, as evident by both rust and by surface mold. However, we don’t know if this is a current or past problem. Atmospheric moisture content in the attic was about the same as outside.

  2. There is excessive temperature in the attic. This is a current problem and often goes hand-in-hand with the moisture problem because they are both indications of poor attic ventilation.

  3. There was no evidence of leaking through the roof. No water stains on the walls or roof sheathing.


Since this write up isn’t an inspection, I can weigh in on possible problems.

  1. The roof ridge vent was not properly installed. It is not unheard of that when the carpenters finish the roof and cut out the approximately 2” of ridge opening from the deck sheathing, that the roofer comes in with the underlayment that is occasionally applied directly over this ridge vent opening, which blocks off the ventilation for actually working.

  2. Since there are two different possible issues, each one with different causes, let’s break it down

    1. Too hot: caused by inadequate ventilation

    2. Too moist: caused by inadequate ventilation, too much moisture penetration from the house, or both.

  3. Extra moisture exposure was occurring because of faulty insulation installation between the main living area and the attic. 

    1. There were areas of sheetrock visible where the insulation had not been properly installed around a raised ceiling area and vapor barrier could not be confirmed for all of the ceiling areas.

    2. The attic access hatch was missing and the home owner had put a thick seat cushion in the hole to provide some blockage. The seal was not 100%


As a home inspector, I need to simply say “call in a roofing or building professional and have the whole system evaluated”. Since there may be other causes that I haven’t even thought of, it’s really only my job to tell you that you have a particular problem and to get help with fixing it.


What Does Moisture Do to a House?


Water itself isn't necessarily the enemy.


Persistent moisture is.

  • Wood can tolerate normal fluctuations in moisture. Building materials can get wet and dry. Problems arise when materials remain wet long enough for deterioration to begin.

  • Persistent moisture can contribute to:

  • Wood decay: Repeated or prolonged wetting can eventually lead to fungal decay and loss of structural integrity.

  • Mold growth: Mold requires moisture, an appropriate temperature, and a food source. Many common building materials provide plenty of food.

  • Corrosion: Metal fasteners, roofing nails, connectors, ducts, and mechanical components can corrode in persistently damp environments.

  • Insulation problems: Wet insulation can lose effectiveness and can remain damp for long periods.

  • Pest activity: Some wood-destroying organisms are strongly associated with damp conditions.

  • Damage to finishes: Drywall, flooring, cabinetry, and other materials can swell, stain, delaminate, or deteriorate.

  • And perhaps most importantly, moisture problems tend to get worse rather than better when the source isn't corrected.


Sebago Inspections looks beyond the obvious signs of water intrusion to identify moisture conditions that may affect the condition, durability, and performance of a home.


 
 
 

Comments


bottom of page